Gasboy DLL2020 Scanner Manuel d'utilisateur télécharger pdf

MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Page 1

Introduction

If you have a Polaris bar code scanner, refer to C35424 Setting Up Your Polaris Bar Code

Scanner.

Your bar code scanner has been programmed at the factory and should be ready to operate.

This document contains a verification sequence that allows you to determine whether your

scanner is programmed correctly, and a programming sequence to follow if it is not

programmed correctly.

Setting Up the Scanner

1 Turn off power to the Profit Point point of sale (POS) terminal.

2 Unplug the AC power to the POS distribution box power supply.

3 Connect the 9-pin RS-232 end of the terminal interface cable to the 9-pin connector on the

scanner.

4 Connect the other end of the terminal interface cable to the SCANNER port on the POS

distribution box and plug in the POS distribution power supply.

5 Turn on the Profit Point POS terminal.

When you turn on the power to the Profit Point, follow the instructions on the screen. The

Profit Point will then initialize and begin Point-of-Sale operations.

Performing Verification Sequence

While in Point-of-Sale operations, scan an item. The scanner should beep when the item is

scanned.

• If the correct item description appears on the screen, the scanner is programmed correctly.

• If the message “# not on file” appears and the number shown on the screen matches the

number under the scanned bar code, the scanner is functioning correctly, but the bar code

cannot be identified. The display may not show the first or the last digit printed on the

item. Press CLEAR MENU to cancel the item entry.

• If the screen does nothing or displays” Data Error on Scanner Port” or “Item Entry Error,”

repeat the scan. If the same message displays, the scanner may be programmed

incorrectly. Proceed with “Programming Sequence” on page 2.

Note: The first time the scanner is turned on, the first scan may produce the error message

“Data Error on Scanner Port” even if the scanner is programmed correctly.

MDE-4389A

Setting Up Datalogic DLL2020 Bar Code

Scanner Used on Profit Point Terminal

September 2005

1 2 3 4 5 6

Résumé du contenu

Page 1 - Setting Up the Scanner

MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Page 1IntroductionIf you have a Polaris bar cod

Page 2 - Programming Sequence

Programming SequencePage 2 MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Programming Sequence

Page 3 - Figure 5: Enter Mode

MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Page 3Programming SequenceFigure 3: Enter ModeF

Page 4 - Figure 7: Parity None

Programming SequencePage 4 MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Figure 6: Baudrate 1

Page 5 - Figure 9: 1 Stopbit

MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal • September 2005 Page 5Programming SequenceFigure 9: 1 StopbitFi

Page 6 - Figure 13: Exit Program Mode

Commentaires sur ces manuels

Pas de commentaire

Gasboy DLL2020 Scanner Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Gasboy DLL2020 Scanner. Gasboy DLL2020 Scanner User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Gasboy DLL2020 Scanner