Gasboy 1000 Series Installing Internal Modem Manuel d'utilisateur télécharger pdf

C35565 7323

FIELD INSTALLATION OF A SERIES 1000 INTERNAL MODEM KIT

When using these instructions for replacement of a defective internal modem, disregard all steps that detail the mounting

of the modem kit hardware (4-8 and 12-13).

The Series 1000 Internal Modem Kit should contain the following parts:

Item Qty P/N Description Item Qty P/N Description

1 2 C01160 Screw, 6-32 x 3/8 Pan Head Slot 7 1 C07122 Modem, internal, 2400

2 1 C34821 Bracket, Phone Jack Cable Assy. 8 1 C05738 Cable Assy., 20-pos. Ribbon Comm

3 2 039069 Nut-Hex Keps # 6-32 Plated 9 1 C02207 Clamp, Ribbon Cable

4 1 C05737 Cable Assy., Phone Jack 10 1 C05356 Cable Assy., Phone Dual (6P/4W)

5 4 C04035 Screw, SS, 6-32 x 1/4 Phillips Pan 11 1 C35565 Field Installation Instructions

6 4 C02896 Support, PC Board 3/8 Long Plastic

1. Unlock and open the rear door of the Series 1000 head.

2. Turn off the AC power switch located to the lower right in the rear of the head.

3. Remove the hood of the unit from the head. This is done by removing the four external screws (two each side) which

secure the hood to the Series 1000 head. Also remove the two internal wing nuts which secure the top of the hood to

the hood support bracket.

4. Remove the MPU PCB by disconnecting all attached cables and removing all of the screws that secure it to the MPU

PCB support plate.

5. Insert the 2 slotted screws (item 1),

through the two holes in the lower left

corner of the MPU PCB support plate

so the heads of the screws are facing

outward. On the inside of the plate,

slip the L-shaped bracket (item 2) over

the screws so the notch in the bracket

is facing the rear of the unit. Secure it

with the keps nuts (item 3).

6. Install the Phone Jack Cable

Assembly (item 4) by sliding it into the

notch of the bracket so the phone jack

faces up and the wires face down.

Push the connector firmly into the

bracket notch.

7. Insert a Phillips head screw (item 5)

through one of the four holes to the

right of the previously installed

bracket, so the head of the screw is

facing outward. Use the screw to

fasten a PC board support (item 6) to

the inside of the plate. Repeat this

procedure until all four supports are

mounted to the inside of the plate.

8. Install the MPU PCB and secure it

with the previously removed screws.

Reconnect all cabling.

1 2

Résumé du contenu

Page 1

C35565 7323FIELD INSTALLATION OF A SERIES 1000 INTERNAL MODEM KITWhen using these instructions for replacement of a defective internal modem, disregar

Page 2

C35565 73239. If replacing a modem, remove the old modem. Install new modem (item 7) by pressing it firmly onto the PC boardsupports until they lock

Modèles reliés 1000 Series Field Installation Internal Modem

Commentaires sur ces manuels

Pas de commentaire

Gasboy 1000 Series Installing Internal Modem Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Gasboy 1000 Series Installing Internal Modem. Gasboy 1000 Series Installing Internal Modem User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 1000 Series Field Installation Internal Modem

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Gasboy 1000 Series Installing Internal Modem